+
  • zl-b560-2.jpg
  • zl-b560-4.jpg
  • zl-b560-3.jpg

编号 :

ZL-B560-S250-100-48-90

2000KG ZL-B560 Damping Steering Drive Wheel



2 tons load capacity per wheel, solid rubber, wheel diameter 452 mm, maximum shock-absorbing capacity of 1.5 tons. Shock Absorption Stroke ±20 mm

Product number:ZL-B560-S250-100-48-90

隐藏域元素占位

  • Product description
  • Most AGV drive wheels are rigid. On a 1.8-tonne platform that is fine until the truck reaches a dock leveller, an expansion joint, or a floor patch that has settled by 8 mm. One wheel lifts, the load shifts onto three, and the steering command starts fighting the chassis instead of turning the wheel. The ZL-B560-S250-100-48-90 puts a ±10 mm sprung suspension under a Ø452 mm solid rubber wheel, so the tyre keeps its contact patch and the steering axis keeps its authority.

     

    It is a steering drive wheel, not a differential unit. 2500 W of traction through a 1:45 reducer, 1000 W of steering through 1:70, both on DC48V, both IP65, with an absolute encoder that reports the steering angle the moment power comes on.

     

     

    Why put a spring under a steering wheel

    A rigid castor works on a flat floor. The trouble starts where the floor changes: a leveller that sits 8 mm proud, a construction joint, a patch of epoxy that has lifted. The wheel takes the load, the chassis lifts, and the steering motor spends its torque fighting the frame instead of turning the wheel. Once the tyre loses contact, the platform also loses its reference — the angle you commanded is no longer the direction the wheel is pointing.

    Suspension does two things at once. It keeps the tyre loaded, and it keeps the steering axis loaded. On the B560 the travel is ±10 mm and the damper is preloaded at 200 kg, so the wheel starts working at a load that matches a real corner of a loaded AGV rather than an empty one.

    ±10 mm of travel, preloaded at 200 kg

    Ten millimetres sounds small. It covers the joint widths and settlement you find in most warehouses, and it is deliberately not enough to let the platform rock. The spring is not there to absorb impact the way a vehicle shock absorber does; it is there to hold the tyre down while the chassis moves. Preload is what makes that work. At 200 kg the damper is already partly compressed at rest, so it pushes back immediately instead of waiting for the first centimetre of travel.

    The drawing shows the unit in its compressed state, which is how it sits under a loaded AGV. Check your chassis height against that number, not against the free length.

    1800 kg on solid rubber — and why there is no polyurethane option

    At this rating the wheel is solid rubber, and the polyurethane column reads N/A. That is not an omission. Polyurethane carries more load per millimetre of width and rolls with less resistance, but it also takes a permanent set under a standing load, and it cuts on grit. At 1800 kg per wheel with a 452 mm diameter, both the contact pressure and the standing load are past what a cast PU tyre holds without flat-spotting. Solid rubber gives up some rolling resistance and takes the load.

    If your platform is lighter and you want polyurethane, the smaller damping wheels in the same series are the right place to look, not this one.

    Two motors, two reducers, one vertical axis

     

    Traction is a 2500 W servo: DC48V, 3000 rpm, 61 A, 7.96 N·m at the motor, through a 1:45 reducer to 358 N·m nominal and 1075 N·m peak at the wheel. That moves 1.5 m/s with a heavy platform and still leaves torque for a ramp start.

     

    Steering is a separate 1000 W servo: DC48V, 3000 rpm, 26.4 A, 3.18 N·m, through 1:70 to 1558 N·m at the steering axis. The two are independent, so a steering correction does not steal torque from traction, and a traction surge does not disturb the steering angle.

     

    Both motors are IP65. The gear pair that carries steering into the chassis is a 20-tooth pinion against a 140-tooth ring gear.

     

    The absolute encoder removes the homing cycle

    Steering feedback is absolute, 65536 counts per revolution. There is no index pulse to find and no homing move at power-up: the controller reads the angle and knows where the wheel points. On a multi-wheel platform that matters more than it sounds, because a homing routine needs clearance to rotate every wheel through a reference, and heavy AGVs rarely have that clearance at the charging station.</p>

    ±120° hard stop with a PNP signal back to the PLC

     

    Steering is limited mechanically at ±120°, and the limit switch reports PNP. The stop protects the cable loom from winding up; the signal lets the controller stop commanding before the mechanics take the load. You need both — a soft limit alone depends on the encoder staying calibrated, and a hard stop alone puts the shock into the gearbox.Fitting it: 560 mm height, Ø695 plate, 12 × M12

     

    The unit stands 560 mm from the mounting face to the floor and is 187 mm wide at the wheel. The top plate is Ø695 mm, drilled 12 × M12 on a Ø360 mm pitch circle. Plan the cut-out and the cable route before you commit the chassis: the steering motor and the traction motor sit on opposite sides, and both need access for wiring and for brake release.

     

    Where the B560 fits — and where it does not

    It fits where a heavy platform has to steer and the floor is not perfect: dock areas, older warehouses with patched concrete, outdoor aprons under a canopy, transfer cars that cross rail recesses. It also fits where the platform is built around one steering wheel and two fixed castors and you need sprung travel to keep all three loaded.

     

    What can be changed for your project

    Wheel compound, gear ratio, encoder type, brake torque, connector and cable length are the usual variables. Send us the platform weight, the number of drive wheels, the floor condition and the steering angle you actually use, and we will confirm which combination holds.

     

     

    Common questions

     

    Can one B560 carry 1800 kg on a four-wheel platform?

    -1800 kg is the rating of the wheel and the traction gear, not an allowance for uneven load distribution. On four wheels, assume one wheel can see more than a quarter of the platform weight whenever the floor is not level. Size the platform so that no single wheel exceeds the rating with that margin left over.

     

    Why is the top speed 1.5 m/s and not higher?

    -1.5 m/s is where this wheel diameter, this gear ratio and this motor still leave margin for acceleration and for a ramp. A higher speed is possible with a different ratio, paid for in starting torque.

    Does the suspension need maintenance?

    -The damper is a sealed gas unit and the moving parts are grease lubricated. There is no oil level to check. Inspect the spring and the linkage for grit and looseness at the same interval you inspect the wheel.

     

    What happens when steering reaches the ±120° stop?

    -The mechanical stop takes the load and the PNP switch changes state. Your controller should read that signal as end of travel and stop commanding rotation. Running into the stop repeatedly will damage the gearbox long before it damages the switch.

     

    What is the difference between the B560 and the B600?

    -The B600 is a damping differential drive unit: it drives, it also can steer. The B560 adds a 1000 W steering motor with its own 1:70 reducer and absolute encoder. If your platform steers by differential speed you do not need this wheel; if it steers by angle you do.

     

    Can the wheel be supplied without the suspension?

    The B560 is built around the sprung linkage. For a rigid version, look at the standard steering drive wheels in the same load class.

     

Related products


undefined

undefined

Products Message


*
*
Submit Message
Wisdom Wheel

Guangzhou Wisdom Wheel Science Technology Ltd.

No. 1436, Guangcong 9th Road, Guangzhou, Guangdong, China

Whatsapp/MB: Kelly +86-18102686399

Jackson +8615012435018

Candy:+86 19396885135

CopyRight © 2024 Guangzhou Wisdom Wheel Science Technology Ltd.

License