+
  • zl-x220-1.jpg

编号 :

ZL-X420

400KG X420 Low-Profile AGV Steering Drive Wheel



400 kg Load capacity single wheel, 160mm wheel diameter, Max speed reach 1.5 m/s, Aluminum Alloy support frame.Small rotational diameter — for latent-lift and low-deck platforms where every millimetre of height is already spent.

Product number:ZL-X420

隐藏域元素占位

  • Product description
  • 420 mm — the number that decides whether this wheel fits
    Low-deck AGVs are built around the wheel, not the other way round. A 160 mm tyre needs clearance under the chassis, and every millimetre of wheel diameter pushes the deck up with it. The X420 sits 223 mm from the mounting face to the floor with a Ø160 mm wheel inside that envelope. If your platform is a latent-lift unit that has to slide under a 150 mm trolley, this is the dimension that gets checked first — before torque, before speed, before anything else on the datasheet.


    The rest of the unit is arranged around that constraint. The traction motor sits horizontally on one side of the housing, the steering motor vertically on the other, and the 1:30 reducer is folded into the space between them rather than hung underneath.

     

    The 400 kg figure belongs to the slewing bearing
    Read the specification line by line: 400 kg is the load rating of the slewing bearing that carries the steering rotation. It is not a claim that the tyre can carry 400 kg at any speed.
    The tyre, the 1:30 planetary reducer and the 400 W motor each have their own limits, and the load a steering wheel actually sees changes with speed, acceleration, floor condition and how often the platform turns. On a steering wheel the tyre also scrubs sideways during every turn, which a straight-line load rating does not describe.
    So use 400 kg for the vertical load on the bearing, and send us the wheel load, the travel speed and the steering frequency separately so the drive side can be checked against your duty cycle.

     

    What "bare unit" means for your bill of materials
    The X420 ships as a mechanical assembly: two Kinco servo motors, the 1:30 traction reducer, the 1:70 steering reducer, the 20/85 gear pair and the limit switch. There is no servo drive, no motion controller and no brake inside it.
    That is deliberate. Most AGV builders have already standardised on a drive family, and shipping a second controller with every wheel creates a spare-part problem on the customer's side. But it does mean the BOM has to carry two servo drives — one for the 400 W traction motor, one for the 50 W steering motor — and a solution for holding the platform when it stops.


    With no built-in brake, a stopped platform on a slope depends on the drive's dynamic braking. That is not the same thing as a mechanical holding brake, and on a ramp it should be checked rather than assumed.

    400 W of traction, 50 W of steering, both Kinco


    Traction is a 400 W Kinco servo: DC48V, 3000 rpm, 10.6 A, 1.27 N·m at the motor shaft, through a two-stage planetary reducer at 1:30 to 38 N·m at the wheel. Top speed is 50 m/min, roughly 0.83 m/s — a walking pace, and about what a 160 mm wheel with a 400 W motor can hold continuously without heat building up in the tyre.


    Steering is a separate 100 W Kinco servo: DC48V, 3000 rpm, 1.5 A, 0.16 N·m, through 1:70 to 45 N·m at the steering axis. Small motor, large reduction. Steering a loaded platform is a low-speed, high-torque job, and the 45 N·m is what turns the wheel against the scrub of a loaded tyre on the floor.
    Because the two axes are independent, a steering correction does not borrow torque from traction, and a traction surge does not disturb the steering angle.

     

    ±108°, not ±120° — and why the difference matters
    The mechanical stop sits at ±108°, and the limit is reported by an NPN proximity switch. 108° is enough to turn a platform through a right angle with margin, and it is 12° short of the ±120° you will see quoted on larger steering wheels.
    If the route planning assumes ±120°, the platform will reach the stop earlier than the path planner expects, and on a tight aisle that shows up as a wheel that stops turning while the controller still commands rotation. Check the steering envelope against your layout before the chassis is cut, and treat the NPN signal as an end-of-travel input rather than a safety circuit.

    85 teeth on the ring, 20 on the pinion, 22 kg on the bench


    Steering is carried by an 85-tooth ring gear driven by a 20-tooth pinion — a 4.25:1 stage in front of the 1:70 reducer. The whole unit weighs 30 kg. That is light enough for two people to lift onto a bench for service, and light enough that fitting it does not force a redesign of the chassis plate.

    Mounting: Ø150 bolt circle, 8 × M6, Ø295 envelope


    The unit mounts on a Ø150 mm bolt circle with 8 × M6 bolts. The largest diameter anywhere in the assembly is Ø295 mm, and total height is 420 mm. Leave clearance for the cable bundle: the grey conduit loops out of the housing and needs its own bend radius, and the two motors sit on opposite sides, so both need access for wiring and for checking the couplings.

    Where the X420 fits — and where it does not

     

    It fits low-deck platforms: latent-lift AGVs, small towing tractors, trolley movers, laboratory and cleanroom carriers, and any chassis where 420 mm is the hard ceiling. It also fits rebuilds where the existing wheel is a 160 mm unit and the deck height cannot change.</p>
    <p>It does not fit a platform that needs IP65 washdown — the X420 is not sealed to that level, and the housing is a machined aluminium body rather than a sealed enclosure. It does not fit a platform that needs a holding brake as standard equipment, or one where the load per steering wheel goes much past 400 kg, because at that point the bearing is the limit and the tyre is no longer the part you should be sizing against.
     

     

    Common questions

     

    Can one X420 really carry 400 kg?
    The slewing bearing can. That is the vertical load the bearing is rated for, and it is the number to use when you divide platform weight across the steering wheels. Whether the tyre and the 400 W motor can move that load at your speed is a separate calculation — send the wheel load, the speed and the acceleration and we will check it.

     

    Why is there no brake?
    The base unit is supplied without one. A 50 W steering motor and a 400 W traction motor are normally held by their drives' dynamic braking, which is enough on level floors. On a ramp, or where the platform has to hold position with power off, a mechanical brake should be specified — ask for it as an option.

     

    Which servo drives do I need?
    Two Kinco-compatible servo drives: one sized for 400 W at DC48V, one for 50 W at DC48V. If you already run Kinco drives on the platform, these are the same family. If you run another brand, the motors can be specified with matching encoders — tell us the drive model before ordering.

     

    Is the X420 available with IP65 or a brake?
    Not as a standard configuration. The X420 is built as a low-height mechanical unit, and sealing the housing adds height. If you need IP65 and can accept 288 mm, the ZL-V288 covers that requirement; if you need a brake, ask for it as an option on the X420.

     

    What is the difference between the X420 and the V288?
    Height and sealing. The X420 is 420 mm tall with a 400 kg slewing bearing and no IP rating. The V288 is 288 mm tall, rated 300 kg, and sealed to IP65. If the deck height is the binding constraint, take the X420; if washdown or dust is the constraint, take the V288.

     

    Can the wheel be replaced separately?
    The polyurethane tyre runs on the wheel hub inside the housing. Tyre replacement is a workshop job rather than a field swap, because the wheel has to come out of the housing to be pressed. Plan the maintenance interval around your duty cycle rather than around a fixed hour count.
     

Related products


undefined

undefined

Products Message


*
*
Submit Message
Wisdom Wheel

Guangzhou Wisdom Wheel Science Technology Ltd.

No. 1436, Guangcong 9th Road, Guangzhou, Guangdong, China

Whatsapp/MB: Kelly +86-18102686399

Jackson +8615012435018

Candy:+86 19396885135

CopyRight © 2024 Guangzhou Wisdom Wheel Science Technology Ltd.

License