编号 :
ZL-V288
300KG Servo Vertical AGV Drive Wheel
Product number:ZL-V288
隐藏域元素占位
- Product description
-
Most vertical drive wheels in this load class are open-frame DC brushed units. They work fine on a clean factory floor. Put one in a washdown bay, a cold store, or a flour-dust line and the brushes, the encoder and the bearing seals all start failing at the same time. The ZL-V288 is the same 288 mm vertical format with everything sealed to IP65 and driven by servo motors instead of brushed ones.

What IP65 actually changes
IP65 means dust-tight and protected against water jets from any direction. In practice that covers three things that kill open drive wheels: high-pressure cleaning at shift change, condensation cycling in and out of a cold room, and fine conductive dust settling on the encoder disc.
Both the traction motor and the steering motor carry the same IP65 rating, and the steering gear runs on grease rather than oil, so there is no oil level to check and nothing to leak if the unit is mounted at an angle.Servo, not brushed
Traction comes from a 400 W servo motor on DC48V, 3000 rpm, 10.6 A, 1.27 N·m at the shaft. Through a 1:30 reducer that becomes 38 N·m nominal at the wheel and 50 m/min of travel.
Servo brings two things a brushed motor cannot. First, closed-loop speed holding: the built-in incremental encoder lets the drive keep an exact commanded speed when the vehicle is pushing a load up a ramp, instead of sagging as current rises. Second, low-speed smoothness — at 2 m/min in a tight docking manoeuvre, a servo holds constant velocity where a brushed unit tends to cog.
48 V rather than 24 V is the other half of that. At the same power the current is roughly halved, which means thinner cable runs, less voltage drop over a long vehicle chassis, and servo drives that stay in their comfortable current range.The 160 mm wheel, in a 288 mm package
The wheel is Ø160 mm, 55 mm wide, polyurethane, rated for 300 kg. The complete assembly measures 288 mm from the mounting face down to the floor — which is where the model number comes from, and it is the number your chassis designer needs.
It mounts on a 190 mm wide plate with a Ø120 mm centre bore and eight M8 threads. The offset from the steering axis to the wheel centre is 180 mm, so check that arc against your frame before committing to a layout.Steering that has good margin
A separate 200 W servo motor drives the steering column through a 1:70 reducer, producing 130 N·m of steering torque. That is deliberately oversized for a 300 kg wheel: it is what lets the unit turn a loaded vehicle out of a tight aisle, or steer against a floor that is not perfectly level, without stalling or hunting.
Mechanical limits sit at ±120° and report through NPN open-collector outputs. The steering axis carries its own incremental encoder, so the controller always knows the wheel angle independently of the traction encoder.Braking
The DC48V brake holds 20 N·m — more than half of the 38 N·m nominal wheel torque. That is a parking brake, not an emergency stop: it is sized to hold a loaded vehicle on a ramp when the drive is disabled, and to stop the wheel creeping during a long dwell.Where it fits — and where it does not
This wheel is for vehicles whose load per wheel stays under 300 kg but whose environment is hostile: food and beverage lines, pharmaceutical and lab logistics, cold-chain order picking, damp basements, dusty processing areas. Small underride AGVs, cleanroom transfer carts and automated lab benches are the typical fits.
It is the wrong choice in two cases. If your load per wheel goes above 300 kg, step up to the , which is the same vertical layout at 1500 kg. If your floor is coarse or your route runs outdoors over expansion joints, a polyurethane tread will not last — and this model does not offer solid rubber, so tell us and we will steer you to a different frame rather than sell you the wrong tread.What can be changed
Cable length and connector type, encoder output format, mounting plate hole pattern and tread hardness can all be adjusted. STEP models are available for chassis integration. Send the load per wheel, the floor surface and the cleaning regime, and we will confirm whether the standard unit fits or a variant is needed.FAQ
1. Can the ZL-V288 be washed down with a hose?
Yes. IP65 covers water jets from any direction, which includes normal washdown practice. It does not cover immersion, and it does not mean you should direct a high-pressure lance at the cable gland from close range — keep 30 cm of distance and avoid prolonged direct spray on the connectors.2. Why is this model 48 V when most of your drive wheels are 24 V?
Because it uses servo motors. Servo drives at this power level are commonly built around 48 V, and the higher bus voltage halves the current for the same output, which matters on a vehicle with a long cable run from the battery box to the wheel.3. How much can four of these carry?
Each wheel is rated 300 kg. A four-wheel layout with even load distribution gives 1200 kg total, but real vehicles rarely distribute load evenly, so plan on 70–80% of the nominal figure for a safety margin unless you have measured the actual corner loads.4. Does the vehicle need a homing routine at startup?
With the standard incremental encoder, yes — the controller needs to find the steering zero once at power-on. If your control architecture cannot do that, ask for the absolute encoder option at the quoting stage.5. What is the difference between the V288 and the V410?
Load and size. The V410 carries 1500 kg and sits taller; the V288 carries 300 kg in a 288 mm package with IP65 sealing throughout. If your vehicle is small and your environment is wet or dusty, the V288 is the right frame. If your vehicle is heavy and your floor is dry and clean, the V410 costs less per kilogram of capacity.
Related products
undefined
Products Message
Products
CopyRight © 2024 Guangzhou Wisdom Wheel Science Technology Ltd.
Powered by www.300.cn SEO Tags En_CityProduct



